Go ahead...point you're finger and laugh
-
- Movin on up ^
- Posts: 324
- Joined: December 5th, 2015, 5:26 pm
- Vehicle Year: 1981
- Vehicle Make: amc
- Vehicle Model: eaglesx4
Go ahead...point you're finger and laugh
My can might be shot. I did my initial break in light revs and short trips with oil system primed and can all lubed up. 1st oil change bad lifter tick when cold and seems to get better as it warms up. Stupid me put in old lifters. Go ahead and laugh I wasn't thinking. What an idiot !!! Go on... If anyone gives a crap and would like to help here's what's going on...
Louder when cold
Cruising speed you hear it
Any acceleration it goes away
Any deceleration it goes away
Idles and starts like a champ
No missing or loss of power
Or just laugh
Louder when cold
Cruising speed you hear it
Any acceleration it goes away
Any deceleration it goes away
Idles and starts like a champ
No missing or loss of power
Or just laugh
- Cheromaniac
- I live here
- Posts: 3258
- Joined: March 8th, 2008, 12:58 pm
- Stroker Displacement: 4563cc
- Vehicle Year: 1992
- Vehicle Make: Jeep
- Vehicle Model: Cherokee
- Location: Cyprus
- Contact:
Re: Go ahead...point you're finger and laugh
I think you already know what you're going to find; cupped lifters and worn cam lobes 'cause you made the mistake of using old lifters on a new cam.
New lifters on an old cam is OK but not the reverse.
Sorry to hear about your troubles and hope you get the engine sorted quickly.
New lifters on an old cam is OK but not the reverse.
Sorry to hear about your troubles and hope you get the engine sorted quickly.
1992 XJ 4.6 I6 - 5MT - Stroker build-up, Stroker "recipes" Sold
1995 Mustang GT - 4AT - Modded Sold
2006 Mustang GT - 5MT - Modded Midlife Crisis Car
1995 Mustang GT - 4AT - Modded Sold
2006 Mustang GT - 5MT - Modded Midlife Crisis Car

-
- Movin on up ^
- Posts: 324
- Joined: December 5th, 2015, 5:26 pm
- Vehicle Year: 1981
- Vehicle Make: amc
- Vehicle Model: eaglesx4
Re: Go ahead...point you're finger and laugh
Thank you. Since there is less than 60 miles on it and I haven't even hit 4000rpms on it yet hopefully the lifter swap solves it. I hope
-
- Strong Poster
- Posts: 922
- Joined: August 15th, 2009, 1:27 am
- Stroker Displacement: 4.7
- Vehicle Year: 2000
- Vehicle Make: Jeep
- Vehicle Model: Cherokee
Re: Go ahead...point you're finger and laugh
Dino is absolutely correct.
At the very least when you pull your lifters out check the bottom of the lifters with a Percision straight edge. Hold it up to a light.
The lifters should have a slight crown. If any of them don't, plan on doing a lifter and camshaft change.
At the very least when you pull your lifters out check the bottom of the lifters with a Percision straight edge. Hold it up to a light.
The lifters should have a slight crown. If any of them don't, plan on doing a lifter and camshaft change.
-
- Movin on up ^
- Posts: 324
- Joined: December 5th, 2015, 5:26 pm
- Vehicle Year: 1981
- Vehicle Make: amc
- Vehicle Model: eaglesx4
Re: Go ahead...point you're finger and laugh
Well I'll find out Wednesday when I pull the head. Hopefully the lifters just took a shit with a higher lift camshaft. If they don't have a slight crown is dead flat okay ? Obviously if they are caved in I got problems. Thanks Russ , didn't want to directly contact about this and take time out of your work day.
-
- Movin on up ^
- Posts: 324
- Joined: December 5th, 2015, 5:26 pm
- Vehicle Year: 1981
- Vehicle Make: amc
- Vehicle Model: eaglesx4
Re: Go ahead...point you're finger and laugh
Shit keeps getting better... just shattered my left wrist a few hours ago playing with my son. Great !
-
- Making Progress
- Posts: 57
- Joined: June 26th, 2008, 9:52 pm
Re: Go ahead...point you're finger and laugh
Darn, what luck. Now, please take the instructions of your doctor to heart. Do as he/she tells you! On the bright side - most of us are right handed. Hope that is the case with you.amceaglesx4 wrote:Shit keeps getting better... just shattered my left wrist a few hours ago playing with my son. Great !
- Cheromaniac
- I live here
- Posts: 3258
- Joined: March 8th, 2008, 12:58 pm
- Stroker Displacement: 4563cc
- Vehicle Year: 1992
- Vehicle Make: Jeep
- Vehicle Model: Cherokee
- Location: Cyprus
- Contact:
Re: Go ahead...point you're finger and laugh
Sorry to hear that. Hope the left isn't your dominant side so you can still do most tasks with the right hand.amceaglesx4 wrote:Shit keeps getting better... just shattered my left wrist a few hours ago playing with my son. Great !
Looks like you'll need a helper to be your left hand while you're working on the Jeep so have some beer & pizza ready.
-
- Movin on up ^
- Posts: 370
- Joined: December 5th, 2013, 1:55 am
- Stroker Displacement: 4.6
- Vehicle Year: 1998
- Vehicle Make: jeep
- Vehicle Model: xj
Re: Go ahead...point you're finger and laugh
That will be interesting, a 'one armed jeep head puller' to change out the lifters. Please post you tube video.
Broken bones only take 6 weeks or 42 days, to heal. 1 down, 41 days to go.
Broken bones only take 6 weeks or 42 days, to heal. 1 down, 41 days to go.
-
- Movin on up ^
- Posts: 324
- Joined: December 5th, 2015, 5:26 pm
- Vehicle Year: 1981
- Vehicle Make: amc
- Vehicle Model: eaglesx4
Re: Go ahead...point you're finger and laugh
Lmfao. This really sucks hardcore. I'm the type that would try anyways. In the way of holding a beer that's what the beer hats are for lmao. Right handed and have to paint, got a family to provide for. As of now all I can do it look under the hood and sigh
- Cheromaniac
- I live here
- Posts: 3258
- Joined: March 8th, 2008, 12:58 pm
- Stroker Displacement: 4563cc
- Vehicle Year: 1992
- Vehicle Make: Jeep
- Vehicle Model: Cherokee
- Location: Cyprus
- Contact:
Re: Go ahead...point you're finger and laugh
Could have been worse. I'm also right-handed and I fractured my right wrist 15 years ago playing soccer, so I very quickly had to learn to write with my left hand for the first two weeks until I could be fitted with a lighter cast.amceaglesx4 wrote:Lmfao. This really sucks hardcore. I'm the type that would try anyways. In the way of holding a beer that's what the beer hats are for lmao. Right handed and have to paint, got a family to provide for. As of now all I can do it look under the hood and sigh
Who is online
Users browsing this forum: Semrush [Bot] and 3 guests