Anyone know the thickness of it?
Anyone using it?
I ran one on my last motor, but it was a stocker and it held up fine, just need to know how thick.
Fel-pro 530sd
-
ajmorell
- Donator
- Posts: 81
- Joined: March 16th, 2009, 11:49 am
- Vehicle Year: 1998
- Vehicle Make: Jeep
- Vehicle Model: ZJ
- Location: Houghton, MI
Re: Fel-pro 530sd
Dunno but it's what I bought and intend on using with my stroker.
-Andy-
MichiganTech Mechanical Engineering
BSME '09
MSME '10
MichiganTech Mechanical Engineering
BSME '09
MSME '10
-
SilverXJ
- Global Moderator
- Posts: 5790
- Joined: February 14th, 2008, 7:14 am
- Stroker Displacement: 4.6L
- Vehicle Year: 2000
- Vehicle Make: Jeep
- Vehicle Model: Cherokee
- Location: Radford, Va
Re: Fel-pro 530sd
.051" Its just a stock replacement gasket.
2000 XJ. 4.6L stroker
00+ Viper Coil Swap | CPS Timing Increase Mod | Fabricated Airbox | Dash bezel, Arduino Multigauge & RD Conceal
Eat, breath, drink, sleep, Jeep, drink
00+ Viper Coil Swap | CPS Timing Increase Mod | Fabricated Airbox | Dash bezel, Arduino Multigauge & RD Conceal
Eat, breath, drink, sleep, Jeep, drink
-
crazygogo
- Making Progress
- Posts: 71
- Joined: December 21st, 2014, 7:38 am
- Stroker Displacement: 242 + .30 over
- Vehicle Year: 2002
- Vehicle Make: jeep
- Vehicle Model: wj
- Location: michigan motorcity
Re: Fel-pro 530sd
is anyone using this head gasket on there engines? and if so do you approve or disapprove of it?
-
PseudoSport
- Where's the "any" key?
- Posts: 26
- Joined: June 23rd, 2011, 2:55 pm
- Stroker Displacement: 4.0L Turbo
- Vehicle Year: 1995
- Vehicle Make: Jeep
- Vehicle Model: Cherokee
Re: Fel-pro 530sd
Used it on a turbo 4.0L and its nothing special, just a stock style gasket. Ended up blowing it above 12 psi so we went with Victor Reinz MLS gasket and have been fine up to 16+ psi. With a stroker any style should be fine and I’d focus more on its thickness and how it effects your quench.
GRM Challenge 1995 2WD Cheorkee, 2,780lbs, 240k 4.0L, 50 trim T3/T4 turbo, MS1 EFI, 36lbs injectors, -2.5 degrees camber, Ford 8.8 3.73 w/LSD, 274 whp/322wtq, 12.98@100mph 1/4 mile
http://www.Facebook.com/JeepXJR
1982 AMC Spirit - Turbo 4.0L, 60 trim T3/T4, MS1 EFI
http://www.Facebook.com/JeepXJR
1982 AMC Spirit - Turbo 4.0L, 60 trim T3/T4, MS1 EFI
-
Torqsplit
- Making Progress
- Posts: 74
- Joined: November 16th, 2010, 2:58 pm
- Stroker Displacement: 4.7
- Vehicle Year: 1992
- Vehicle Make: Jeep
- Vehicle Model: XJ
Re: Fel-pro 530sd
One thing to consider is the bore-size if using a standard replacement gasket in "0"-deck setups. There's potential for piston interference with the 3.875" gasket. Looks like the 530SD is spec'd @ 4.00 so you good there. Apparently PseudoSport pushed one pretty far before having any trouble, so I'd feel pretty confident with it! Good Luck with your build 
Who is online
Users browsing this forum: Google [Bot] and 3 guests