What clutch to run with Ax-15 and stroker
-
- Where's the "any" key?
- Posts: 20
- Joined: December 16th, 2011, 1:08 pm
- Stroker Displacement: 4.6
- Vehicle Year: 1995
- Vehicle Make: jeep
- Vehicle Model: wrangler
What clutch to run with Ax-15 and stroker
Gettin ready to install my stroker, based on Rockcrawler build, gonna reuse my Ax-15, what clutch should I run, I assume stock will not cut it. Thanks
- SilverXJ
- Global Moderator
- Posts: 5790
- Joined: February 14th, 2008, 7:14 am
- Stroker Displacement: 4.6L
- Vehicle Year: 2000
- Vehicle Make: Jeep
- Vehicle Model: Cherokee
- Location: Radford, Va
Re: What clutch to run with Ax-15 and stroker
I don't know whether the stock one will hold or not, but I have heard Luk clutches are highly recommended.
2000 XJ. 4.6L stroker
00+ Viper Coil Swap | CPS Timing Increase Mod | Fabricated Airbox | Dash bezel, Arduino Multigauge & RD Conceal
Eat, breath, drink, sleep, Jeep, drink
00+ Viper Coil Swap | CPS Timing Increase Mod | Fabricated Airbox | Dash bezel, Arduino Multigauge & RD Conceal
Eat, breath, drink, sleep, Jeep, drink
-
- I made it to triple digits!
- Posts: 137
- Joined: November 27th, 2011, 9:24 pm
- Vehicle Year: 1995
- Vehicle Model: XJ
Re: What clutch to run with Ax-15 and stroker
likely a Center Force DF or ACT kits would hold the tq
- IH 392
- I love JeepStrokers.com!!
- Posts: 725
- Joined: October 4th, 2008, 11:15 am
- Location: Eugene ORYGUN
- Contact:
Re: What clutch to run with Ax-15 and stroker
I got an OE SACHS clutch to run with my stroker, the OE one in my Jeep now has 147K miles on it and has NEVER once offered to slip!?, the AX-15's on the 4.0's use a 10.4" disk, that's V8 territory!
You can get more power out of ANY engine!!!
ASE Master certified engine machinist, gas and diesel
ASE Master certified engine machinist, gas and diesel
- Missourian
- Donator
- Posts: 142
- Joined: July 5th, 2011, 3:51 pm
- Stroker Displacement: 4.6L
- Vehicle Year: 2000
- Vehicle Make: Jeep
- Vehicle Model: Wrangler
- Location: K.C. Metro Area
- Contact:
Re: What clutch to run with Ax-15 and stroker
I opted to go with the Centerforce II to go behind my STROKER being installed here shortly.
-
- Where's the "any" key?
- Posts: 20
- Joined: December 16th, 2011, 1:08 pm
- Stroker Displacement: 4.6
- Vehicle Year: 1995
- Vehicle Make: jeep
- Vehicle Model: wrangler
Re: What clutch to run with Ax-15 and stroker
I've heard some other people say stock will hold up, where is the best place to get a luk clutch and which one should I get
-
- Where's the "any" key?
- Posts: 20
- Joined: December 16th, 2011, 1:08 pm
- Stroker Displacement: 4.6
- Vehicle Year: 1995
- Vehicle Make: jeep
- Vehicle Model: wrangler
Re: What clutch to run with Ax-15 and stroker
Ordered a Luk Pro Gold for 151.00 from partsgeek
-
- Noob
- Posts: 10
- Joined: January 1st, 2012, 3:05 pm
- Vehicle Year: 1998
- Vehicle Make: Jeep
- Vehicle Model: Cherokee
- Location: Kimberley B.C. Canada
Re: What clutch to run with Ax-15 and stroker
What about SPEC clutches? Like the SD651? I run a high hp SPEC clutch in my mustang and love it. No slip, easy pedal. Anyone ever used one in a Jeep before?
http://www.redlinemotive.com/part-numbe ... /sd651.asp
http://www.redlinemotive.com/part-numbe ... /sd651.asp
98 XJ 2dr 4.0L, 4.5" and 33's
97 XJ 4.0L, 2" and 235/75's
87 XJ Wagoneer 4.0L, 5" and 33's
93 XJ 4.0L (Dad's) 2" and 235/75's
97 TJ 4.0L (GF's), 4" and 33's
97 XJ 4.0L, 2" and 235/75's
87 XJ Wagoneer 4.0L, 5" and 33's
93 XJ 4.0L (Dad's) 2" and 235/75's
97 TJ 4.0L (GF's), 4" and 33's
- Winners97TJ
- Learning to use the board
- Posts: 35
- Joined: August 23rd, 2010, 2:02 pm
- Stroker Displacement: 4.7L - In Progress
- Vehicle Year: 1997
- Vehicle Make: Jeep
- Vehicle Model: Wrangler
- Location: Round Rock, TX
Re: What clutch to run with Ax-15 and stroker
I bought my SACHS clutch from O'Reilly's. My stock clutch measured at 1.5mm thinner than the new one after 150k miles! After seeing that, I was sold. It was only $130! Not only that, O'Reillys has a lifetime warranty on 'em. I'm not anticipating any issues, but if there are, I'll let ya know! Should have everything back in and running by next weekend.
Who is online
Users browsing this forum: No registered users and 3 guests