4.7l forged turbo build underway
-
- Learning to use the board
- Posts: 34
- Joined: September 24th, 2010, 6:05 pm
- Stroker Displacement: 4.7
- Vehicle Year: 1997
- Vehicle Make: Jeep
- Vehicle Model: Cherokee
Re: 4.7l forged turbo build underway
Yea thats why they are blue there. They are really nice lookin rods. I am actually going with a little different cam. 218/224 ...better for a turbo then the cam I originally listed......really dont want to spin the motor over 6. And since its an auto i dont want to have to run a high stall and i would with the 226/234 cam.
Im lookin to get around 320-330 n/a, and im shootin for 450-500 on boost at the crank. If i can make 350-400rwhp id be pretty damn happy. I may be able to make more but ill have to see how it does once the turbo is on. The motor should be able to handle 20psi or so but id prob only run that much at the track
Im lookin to get around 320-330 n/a, and im shootin for 450-500 on boost at the crank. If i can make 350-400rwhp id be pretty damn happy. I may be able to make more but ill have to see how it does once the turbo is on. The motor should be able to handle 20psi or so but id prob only run that much at the track
-
- Learning to use the board
- Posts: 34
- Joined: September 24th, 2010, 6:05 pm
- Stroker Displacement: 4.7
- Vehicle Year: 1997
- Vehicle Make: Jeep
- Vehicle Model: Cherokee
Re: 4.7l forged turbo build underway
Also I live in colorado, elevation here in Calhan where i live is 6,500ft. Both tracks I go to are 4,900ft and 5,900ft.
- TurboTom
- I made it to triple digits!
- Posts: 191
- Joined: August 25th, 2008, 11:11 pm
- Location: Winchester Virginia
- Contact:
Re: 4.7l forged turbo build underway
I made almost 500 ft/lbs and 450 HP at 13 lbs on my 4.0, so you should have no problem meeting your goals.
Remember, Sometimes I post after drinking!
1979 AMC Spirit
Building a Turbo 2.5
I am not very smart!
1979 AMC Spirit
Building a Turbo 2.5
I am not very smart!
-
- Learning to use the board
- Posts: 34
- Joined: September 24th, 2010, 6:05 pm
- Stroker Displacement: 4.7
- Vehicle Year: 1997
- Vehicle Make: Jeep
- Vehicle Model: Cherokee
Re: 4.7l forged turbo build underway
Wow...those are good numbers.
I guess I'll be the first to find out. Im sure whatever I end up making, it will still be a blast to drive.
I guess I'll be the first to find out. Im sure whatever I end up making, it will still be a blast to drive.
-
- Learning to use the board
- Posts: 34
- Joined: September 24th, 2010, 6:05 pm
- Stroker Displacement: 4.7
- Vehicle Year: 1997
- Vehicle Make: Jeep
- Vehicle Model: Cherokee
Re: 4.7l forged turbo build underway
Head is on, rockers on, and head is painted. (chrysler red)
You do not have the required permissions to view the files attached to this post.
- SilverXJ
- Global Moderator
- Posts: 5790
- Joined: February 14th, 2008, 7:14 am
- Stroker Displacement: 4.6L
- Vehicle Year: 2000
- Vehicle Make: Jeep
- Vehicle Model: Cherokee
- Location: Radford, Va
Re: 4.7l forged turbo build underway
Those are the ARP head bolts? What is the part number? I thought ARP didn't make a direct fit set for the 4.0L
2000 XJ. 4.6L stroker
00+ Viper Coil Swap | CPS Timing Increase Mod | Fabricated Airbox | Dash bezel, Arduino Multigauge & RD Conceal
Eat, breath, drink, sleep, Jeep, drink
00+ Viper Coil Swap | CPS Timing Increase Mod | Fabricated Airbox | Dash bezel, Arduino Multigauge & RD Conceal
Eat, breath, drink, sleep, Jeep, drink
-
- Learning to use the board
- Posts: 34
- Joined: September 24th, 2010, 6:05 pm
- Stroker Displacement: 4.7
- Vehicle Year: 1997
- Vehicle Make: Jeep
- Vehicle Model: Cherokee
Re: 4.7l forged turbo build underway
Yea they are. I might have to wait till i get home and look at the sheet that came with them but I got them from 505 performance. Ill check the paper out for ya when I get home. Probably be about 2hrs or so.
-
- Learning to use the board
- Posts: 34
- Joined: September 24th, 2010, 6:05 pm
- Stroker Displacement: 4.7
- Vehicle Year: 1997
- Vehicle Make: Jeep
- Vehicle Model: Cherokee
Re: 4.7l forged turbo build underway
I checked the paper out. There was not a part number anywhere on it.
-
- Learning to use the board
- Posts: 34
- Joined: September 24th, 2010, 6:05 pm
- Stroker Displacement: 4.7
- Vehicle Year: 1997
- Vehicle Make: Jeep
- Vehicle Model: Cherokee
Re: 4.7l forged turbo build underway
Timing cover and oil pan on
You do not have the required permissions to view the files attached to this post.
-
- Learning to use the board
- Posts: 34
- Joined: September 24th, 2010, 6:05 pm
- Stroker Displacement: 4.7
- Vehicle Year: 1997
- Vehicle Make: Jeep
- Vehicle Model: Cherokee
Re: 4.7l forged turbo build underway
Intake manifold on, header on, injectors on, throttle body on, alternator and motor mounts on. It will be ready to go back in my jeep this weekend.
Still have to clean up the engine compartment this week.
Still have to clean up the engine compartment this week.
You do not have the required permissions to view the files attached to this post.
-
- Learning to use the board
- Posts: 34
- Joined: September 24th, 2010, 6:05 pm
- Stroker Displacement: 4.7
- Vehicle Year: 1997
- Vehicle Make: Jeep
- Vehicle Model: Cherokee
Re: 4.7l forged turbo build underway
Dropped the motor back in the jeep last night. Just need a water pump, plugs ard wires and oil. I am goin to get everything hooked back up and hopefully start it for the first time next weekend.
You do not have the required permissions to view the files attached to this post.
-
- Where's the "any" key?
- Posts: 22
- Joined: October 5th, 2010, 4:31 pm
- Stroker Displacement: 4.7
- Vehicle Year: 1987
- Vehicle Make: jeep
- Vehicle Model: comanche
Re: 4.7l forged turbo build underway
So what going on now , its been almost a year since your motor went in. Now ?
-
- BANNED
- Posts: 297
- Joined: December 3rd, 2011, 2:01 am
- Vehicle Year: 1998
- Vehicle Make: Jeep
- Vehicle Model: Cherokee
Re: 4.7l forged turbo build underway
Any update?
1998 XJ 2D AW4 32"MTR 3.55 4.5"RC JCR Slider Magnaflow 150rwHP/174rwTQ=> Sprintex SC Gibson Header 6lb 120-140*IAT 211rwHP/274rwTQ WasherFluid Inj 70mmTB 7.5lb 100-120*IAT=>Now 12 pounds Boost=> +BV ported head
99 XJ M62 S/C
99 XJ M62 S/C
Who is online
Users browsing this forum: No registered users and 16 guests