An forum is to exchange experience and help people with the same interests.
I have to say thank you to all people for your respond here and your PM's Specially to Cheromaniac (was my pleasure to meet you today)
Not sure how helpful it is for future stroker builders, but this here is my result for the part list to build my 4.7 liter stroker for the 2001 XJ
I will close this thread here from my side and start Phase 2: collecting of parts!
Part list
Parts List
Needed to Order in the USA 7 summitracing:
6 Pistons with rings:
http://www.summitracing.com/parts/UEM-IC944KTM-060/
Keith Black/KB Pistons IC944-060
1 Camshaft:
http://www.summitracing.com/parts/CCA-68-231-4/
COMP Cams 68-231-4
12 Valve springs:
http://www.summitracing.com/parts/DCC-5249464/
Mopar Performance P5249464
12 Valve spring retainers:
http://www.summitracing.com/parts/DCC-4452032/
Mopar Performance P4452032
12 Valve keepers:
http://www.summitracing.com/parts/DCC-4529218/
Mopar Performance P4529218
6 Injectors:
http://www.summitracing.com/parts/ACC-150824/
ACCEL 150824 - ACCEL Fuel Injectors
1 Flowkooler water pump:
http://www.summitracing.com/parts/BRA-1747/
FlowKooler 1747
1 JET 180* thermostat:
http://www.summitracing.com/parts/JET-10170/
JET Performance 10170
12 Roller Rockers.
http://www.summitracing.com/parts/CSP-S40196/
Harland Sharp S40196
12 connecting rod bolts
http://www.summitracing.com/parts/ARP-112-6001/
ARP 112-6001 - ARP High Performance Connecting Rod Bolt Kits
And little extra power
1Nitrous Injection Kit 50 HP
http://www.summitracing.com/parts/VNM-N48-137/
VENOM High Performance N48-137
Screw for cam shaft with trust pin (not clear where to get it from but needed)
To get here from UAE:
- Block 2000/2001 Casting No. 53010449AA
- Cylinder head from 2002/2006 Wrangler with TUPY stamp, or 2000/2001 with casting # 0360
- Oil Pan
- Valve cover
- Throttle body
- crank shaft 258 - 4.2 liter with 12 counter weights
For the cylinder head (all from Mopar):
1) 6 VALVE, Intake
2) 6 SEAL, Valve Guide intake (not sure maybe not needed with the mopar performance springs)
3) 6 VALVE, Exhaust
4) 6 SEAL, Valve Guide exhaust (not sure maybe not needed with the mopar performance springs)
5)
!!No PIVOT, for the Rocker Arm and NO BRIDGE, for the Rocker Arm!!
6) 12 Tappet, Valve
7) 12 Pushrods, Valve (standard 4,0L!)
8) 1 Gasket, Valve Cover
9) 1 Gasket, Cylinder Head
For crank and Pistons (all from Mopar):
10) 12 Main Bearing, Crankshaft (12 pieces each half round) Picture 1
11) 1 Thrust Bearing,Crankshaft
12) 12 Bearing, Connecting Rod & 6 Rods (12 pieces each half round)
13) Set of 5 Bearing, Camshaft (still for the stock 4.0L?)
14) 1Gasket, Manifold
15) 1 GEAR, Crankshaft ( in the timing chain set)
16) 1 SLINGER, Oil Slinger next to Gear (in the timing chain set)
17) 1Bearing, Crankshaft Pilot
18) 1 timing chain and 2 sprockets
19) 1 Gasket & Seal Kit, Timing (in the timing chain set)
Block and accessories (all from Mopar)::
20) 1Gasket Set, Oil Pan
21) 1Filter, Engine Oil
22) 1Oilpump
XX) freeze plugs