Distributor Clamp?
- Jeep4xb4u
- Donator
- Posts: 75
- Joined: August 3rd, 2008, 6:44 pm
- Stroker Displacement: 4.6L
- Vehicle Year: 1988
- Vehicle Make: XJ 2dr
- Vehicle Model: Sport
- Location: BAY AREA / CA
- Contact:
Distributor Clamp?
Just curious what everyone is using for a clamp after they cut the ears off. I snagged a cheep one from Autozone for a SB and its on there with a little modification but i don't trust it. I know a 4.2l one works but has anyone found another solution?
88' XJ 2dr
4.0l / AW4 / NP231 / D35c
6.5" Long Arm Lift - 33x12.5's - 15x8 Mickey's
Currently working on 4.6l / D44 Swap
4.0l / AW4 / NP231 / D35c
6.5" Long Arm Lift - 33x12.5's - 15x8 Mickey's
Currently working on 4.6l / D44 Swap
-
- Donator
- Posts: 247
- Joined: July 31st, 2008, 12:28 pm
Re: Distributor Clamp?
What about one off of the distributer-less ignition? The cam position sensor is held down by a clamp. That may work.
- Jeep4xb4u
- Donator
- Posts: 75
- Joined: August 3rd, 2008, 6:44 pm
- Stroker Displacement: 4.6L
- Vehicle Year: 1988
- Vehicle Make: XJ 2dr
- Vehicle Model: Sport
- Location: BAY AREA / CA
- Contact:
Re: Distributor Clamp?
This is a good idea. Ill have to check into this by pulling the clamp off the WJ and testing it on the stroker. I see no reason why it wouldn't work the boss on the sensor and my dizzy look very similar now that the ears are shaved off.Bodo wrote:What about one off of the distributer-less ignition? The cam position sensor is held down by a clamp. That may work.
88' XJ 2dr
4.0l / AW4 / NP231 / D35c
6.5" Long Arm Lift - 33x12.5's - 15x8 Mickey's
Currently working on 4.6l / D44 Swap
4.0l / AW4 / NP231 / D35c
6.5" Long Arm Lift - 33x12.5's - 15x8 Mickey's
Currently working on 4.6l / D44 Swap
- Jeep4xb4u
- Donator
- Posts: 75
- Joined: August 3rd, 2008, 6:44 pm
- Stroker Displacement: 4.6L
- Vehicle Year: 1988
- Vehicle Make: XJ 2dr
- Vehicle Model: Sport
- Location: BAY AREA / CA
- Contact:
Re: Distributor Clamp?
Confirmed.
2002 4.0l Cam sensor clamp fits my distributer. I would assume it would fits all.
Thanks Bodo
2002 4.0l Cam sensor clamp fits my distributer. I would assume it would fits all.
Thanks Bodo
88' XJ 2dr
4.0l / AW4 / NP231 / D35c
6.5" Long Arm Lift - 33x12.5's - 15x8 Mickey's
Currently working on 4.6l / D44 Swap
4.0l / AW4 / NP231 / D35c
6.5" Long Arm Lift - 33x12.5's - 15x8 Mickey's
Currently working on 4.6l / D44 Swap
-
- Donator
- Posts: 247
- Joined: July 31st, 2008, 12:28 pm
Re: Distributor Clamp?
Sure thing! Glad I could be of assistance.
Who is online
Users browsing this forum: No registered users and 22 guests