Welcome to www.JeepStrokers.com!!
Not yet a registered user? You are required to Register before you can post within this topic.

4.8 stroker build

Project vehicle blogs or "mod diary" specific threads only.. Pics encouraged!!
cal
Learning to use the board
Learning to use the board
Posts: 30
Joined: March 19th, 2008, 12:09 pm
Stroker Displacement: 4.71

Re: 4.8 stroker build

Post by cal » January 31st, 2019, 7:43 pm

Wait what


Why

cal
Learning to use the board
Learning to use the board
Posts: 30
Joined: March 19th, 2008, 12:09 pm
Stroker Displacement: 4.71

Re: 4.8 stroker build

Post by cal » January 31st, 2019, 8:51 pm

NM. Misread.

User avatar
SkylinesSuck
Donator
Donator
Posts: 431
Joined: February 14th, 2009, 11:11 pm
Stroker Displacement: 4.6L
Vehicle Year: 1998
Vehicle Make: Jeep
Vehicle Model: Wrangler
Location: Northern VA

Re: 4.8 stroker build

Post by SkylinesSuck » February 1st, 2019, 4:34 am

I'm still confused like you were before re-reading. Help?

cal
Learning to use the board
Learning to use the board
Posts: 30
Joined: March 19th, 2008, 12:09 pm
Stroker Displacement: 4.71

Re: 4.8 stroker build

Post by cal » February 1st, 2019, 6:20 am

He was deshrouding the area around the valves. He just worded it weird and scribing the 4" bore was confusing, but makes sense to me now.

User avatar
SkylinesSuck
Donator
Donator
Posts: 431
Joined: February 14th, 2009, 11:11 pm
Stroker Displacement: 4.6L
Vehicle Year: 1998
Vehicle Make: Jeep
Vehicle Model: Wrangler
Location: Northern VA

Re: 4.8 stroker build

Post by SkylinesSuck » February 1st, 2019, 9:54 am

I'm tracking now. Thanks.

GreenYJ
I think I'll order a "tab"
I think I'll order a "tab"
Posts: 40
Joined: October 21st, 2016, 2:02 pm
Vehicle Year: 1994
Vehicle Make: Jeep
Vehicle Model: Wrangler

Re: 4.8 stroker build

Post by GreenYJ » February 2nd, 2019, 6:20 pm

Sorry. That was the best way I could come up to describe it at the time. I didn't take a picture.

I bolted the head to the bare block. I then reached up into the cylinders from the bottom with a scribe and marked the cylinder head where the 4" bore meets the cylinder head. The flat surface of the head was hanging in the cylinder all the way around the bore. I left the 2 quench areas and unshrouded the valves out to the scribed line. I hope that makes better sense.
1994 Sahara YJ

User avatar
SkylinesSuck
Donator
Donator
Posts: 431
Joined: February 14th, 2009, 11:11 pm
Stroker Displacement: 4.6L
Vehicle Year: 1998
Vehicle Make: Jeep
Vehicle Model: Wrangler
Location: Northern VA

Re: 4.8 stroker build

Post by SkylinesSuck » February 3rd, 2019, 2:43 am

At first glance, I think we both read it as you were going to remove material from the head everywhere inside the scribed line including the squish pads.

cal
Learning to use the board
Learning to use the board
Posts: 30
Joined: March 19th, 2008, 12:09 pm
Stroker Displacement: 4.71

Re: 4.8 stroker build

Post by cal » February 12th, 2019, 4:30 pm

^^ exactly. it was the scribed line that confused us. totally makes sense though looking at it now.

Post Reply

Who is online

Users browsing this forum: No registered users and 5 guests