AEM F/IC Basic Setup
- gradon
- Donator
- Posts: 1353
- Joined: February 13th, 2008, 5:33 pm
- Stroker Displacement: 4.6/280ci
- Vehicle Year: 1996
- Vehicle Make: Jeep
- Vehicle Model: Cherokee
- Location: DC
Re: AEM F/IC Basic Setup
I found that 4.7Kohm-10Kohm resistors allowed you to offset the O2 voltages without the pcm fighting you.
- darkcorp
- I made it to triple digits!
- Posts: 101
- Joined: November 14th, 2013, 12:21 am
- Stroker Displacement: 4.6L
- Vehicle Year: 1999
- Vehicle Make: JEEP
- Vehicle Model: GCh 4.0
- Location: Kazan/Russia
- Contact:
Re: AEM F/IC Basic Setup
Hi guys!
I've bought AEM FIC 6 1910 for my 4.6 stroker. I know for Chrysler engine I should use 1913 version to eliminate MIL for injectors but I've found only 1910 version in my country.
One of my mate uses AEM FIC 6 1910 without throwing MIL. He connected additional 6 old Jeep injectors from junkyard and it works well.
Is it right or I can add some inductor coils instead? If yes, then could you tell parameters of inductor?
I've bought AEM FIC 6 1910 for my 4.6 stroker. I know for Chrysler engine I should use 1913 version to eliminate MIL for injectors but I've found only 1910 version in my country.
One of my mate uses AEM FIC 6 1910 without throwing MIL. He connected additional 6 old Jeep injectors from junkyard and it works well.
Is it right or I can add some inductor coils instead? If yes, then could you tell parameters of inductor?
You do not have the required permissions to view the files attached to this post.
- darkcorp
- I made it to triple digits!
- Posts: 101
- Joined: November 14th, 2013, 12:21 am
- Stroker Displacement: 4.6L
- Vehicle Year: 1999
- Vehicle Make: JEEP
- Vehicle Model: GCh 4.0
- Location: Kazan/Russia
- Contact:
Re: AEM F/IC Basic Setup
I don't understand why one picture wasn't attached.
You do not have the required permissions to view the files attached to this post.
- darkcorp
- I made it to triple digits!
- Posts: 101
- Joined: November 14th, 2013, 12:21 am
- Stroker Displacement: 4.6L
- Vehicle Year: 1999
- Vehicle Make: JEEP
- Vehicle Model: GCh 4.0
- Location: Kazan/Russia
- Contact:
Re: AEM F/IC Basic Setup
Hi guys!
Can you show basic settings for AEM FIC 6 for Jeep?
I've installed AEM, but engine roughly starts and stop in second. MAP shows 9kpa instead of 100 kpa on stopped engine.
Can you show basic settings for AEM FIC 6 for Jeep?
I've installed AEM, but engine roughly starts and stop in second. MAP shows 9kpa instead of 100 kpa on stopped engine.
-
- I made it to triple digits!
- Posts: 146
- Joined: May 14th, 2016, 10:29 am
- Vehicle Year: 1996
- Vehicle Make: Jeep
- Vehicle Model: Cherokee
Re: AEM F/IC Basic Setup
What is your map clamp voltage set to? Map is an intercept connection. Map "in" goes from the sensor to the FIC, map "out" goes from the FIC to the PCM.
- darkcorp
- I made it to triple digits!
- Posts: 101
- Joined: November 14th, 2013, 12:21 am
- Stroker Displacement: 4.6L
- Vehicle Year: 1999
- Vehicle Make: JEEP
- Vehicle Model: GCh 4.0
- Location: Kazan/Russia
- Contact:
Re: AEM F/IC Basic Setup
Checked wiring, it's ok.
Gave 1.5V to MAF input to FIC (1.5V battery), AEM shows 1.5V in program and gives 1.5V to ecu.
Gave 1.5V to MAF input to FIC (1.5V battery), AEM shows 1.5V in program and gives 1.5V to ecu.
-
- I made it to triple digits!
- Posts: 146
- Joined: May 14th, 2016, 10:29 am
- Vehicle Year: 1996
- Vehicle Make: Jeep
- Vehicle Model: Cherokee
Re: AEM F/IC Basic Setup
Start a new thread detailing your set up. I can only assume what you have for a set up but try to Zero out your MAP map. In the settings menu put your map clamp max to 4.9v. Does it run? Does it run correctly with stock injectors and bypass harness?
- darkcorp
- I made it to triple digits!
- Posts: 101
- Joined: November 14th, 2013, 12:21 am
- Stroker Displacement: 4.6L
- Vehicle Year: 1999
- Vehicle Make: JEEP
- Vehicle Model: GCh 4.0
- Location: Kazan/Russia
- Contact:
Re: AEM F/IC Basic Setup
Can you show me your setup settings please?
Here are mine
Here are mine
You do not have the required permissions to view the files attached to this post.
- darkcorp
- I made it to triple digits!
- Posts: 101
- Joined: November 14th, 2013, 12:21 am
- Stroker Displacement: 4.6L
- Vehicle Year: 1999
- Vehicle Make: JEEP
- Vehicle Model: GCh 4.0
- Location: Kazan/Russia
- Contact:
Re: AEM F/IC Basic Setup
Finally started!
-
- I made it to triple digits!
- Posts: 146
- Joined: May 14th, 2016, 10:29 am
- Vehicle Year: 1996
- Vehicle Make: Jeep
- Vehicle Model: Cherokee
Re: AEM F/IC Basic Setup
What was it?
- darkcorp
- I made it to triple digits!
- Posts: 101
- Joined: November 14th, 2013, 12:21 am
- Stroker Displacement: 4.6L
- Vehicle Year: 1999
- Vehicle Make: JEEP
- Vehicle Model: GCh 4.0
- Location: Kazan/Russia
- Contact:
Re: AEM F/IC Basic Setup
Couldn't say exactly. Maybe harness or maybe base settings.
How do you start to tune AEM FIC on stroker?
How do you start to tune AEM FIC on stroker?
-
- I made it to triple digits!
- Posts: 146
- Joined: May 14th, 2016, 10:29 am
- Vehicle Year: 1996
- Vehicle Make: Jeep
- Vehicle Model: Cherokee
Re: AEM F/IC Basic Setup
Start a new thread with the details of your build.
Who is online
Users browsing this forum: No registered users and 9 guests