Welcome to www.JeepStrokers.com!!
Not yet a registered user? You are required to Register before you can post within this topic.

4.6 crawler build - low end torque....

Project vehicle blogs or "mod diary" specific threads only.. Pics encouraged!!
User avatar
SkylinesSuck
Donator
Donator
Posts: 388
Joined: February 14th, 2009, 11:11 pm
Stroker Displacement: 4.6L
Vehicle Year: 1998
Vehicle Make: Jeep
Vehicle Model: Wrangler
Location: Northern VA

Re: 4.6 crawler build - low end torque....

Post by SkylinesSuck » November 1st, 2018, 1:53 pm

They all work now! :rockout:

TJryder
Learning to use the board
Learning to use the board
Posts: 31
Joined: July 29th, 2018, 1:03 pm
Stroker Displacement: 4.6
Vehicle Year: 2000
Vehicle Make: Jeep
Vehicle Model: TJ

Re: 4.6 crawler build - low end torque....

Post by TJryder » November 3rd, 2018, 12:16 am

To continue the build log...

I started to build adapter plate to adapt the bolt pattern of V8 4.7 throttle body to I6 throttle body bolt pattern.

Side effect is that I will also get this infamous 25 throttle body spacer that should (but proven not) bring some extra HP :doh:

Anyway - I started with 25mm (1") thick 7075 aluminum stock:

Image

I first marked one hole, drilled it an taped with M8 tap.

As usual - first hole always fit. Si I bolted it down firmly, marked and drill / tap the rest:
Image

Now to the sketchy part - the lathe. I wish I would not throw in that taper so early :huh: .

First 4mm center drill, than 13mm to make way for the boring bar. Sketchy.... But it went OK.

Image

Image

But it did work out just fin, I just had to bore out the hole on a slower pace, 1.5mm pass.

Image

In the end - it worked out just fine:
Image

Now to the mount bolt pattern....
°O I I I I I I O°

TJryder
Learning to use the board
Learning to use the board
Posts: 31
Joined: July 29th, 2018, 1:03 pm
Stroker Displacement: 4.6
Vehicle Year: 2000
Vehicle Make: Jeep
Vehicle Model: TJ

Re: 4.6 crawler build - low end torque....

Post by TJryder » November 7th, 2018, 12:25 pm

I went to see the 4.0 2002 TJ engine today.
Looks nice. But again different than the one I have....
It has new ignition system without distributor...
It comes complete with harness, gearbox etc...
I guess I can convert it back to distributor or is it a benifit to keep the new type of ignition?

BR M
°O I I I I I I O°

TJryder
Learning to use the board
Learning to use the board
Posts: 31
Joined: July 29th, 2018, 1:03 pm
Stroker Displacement: 4.6
Vehicle Year: 2000
Vehicle Make: Jeep
Vehicle Model: TJ

Re: 4.6 crawler build - low end torque....

Post by TJryder » November 13th, 2018, 12:49 pm

Well, made some small progress on the build...

Opened up idle air passage on the new TB:
Image

and modified the linkage according to Martin's video. Only comment - when you bend the stop tab - you have to re weld it. Mine started to crack...

Than I moved over to 07120 head stripping. I made myself a tool using standard woodworker clamp and turned / milled an attachment:

Image

It went apart really nicely.

Image

Some valves are in great condition, some are slightly worn, especially exhaust valves.

I measured 0.02mm wear = 0.00078". Not knowing the way the head is bult and doing the window shopping at performance&spare part stores - I was looking for replacement valves and new guides. But - yes you are smiling now - there are no guides in the original head :shock:

Well, first american engine that I am working on in depth. 30 years older Alfa had dual overhead cams in aluminium head with bronze valve guides. Cast iron - OK, why not :-)

So, what are my options? Are there any oversize vales and that fit reamed guide bore? Machining for new those bought insert - not really an option locally as I have limited access to good machine shops.. One recommended by a guy who helped me on my C3 project - but also recommended to avoid this job...

HELP! Or shall I just by new exhaust valves and live it as it is?
°O I I I I I I O°

User avatar
SkylinesSuck
Donator
Donator
Posts: 388
Joined: February 14th, 2009, 11:11 pm
Stroker Displacement: 4.6L
Vehicle Year: 1998
Vehicle Make: Jeep
Vehicle Model: Wrangler
Location: Northern VA

Re: 4.6 crawler build - low end torque....

Post by SkylinesSuck » November 13th, 2018, 1:29 pm

Wow. Well, no help here but looking forward to hear what the experts have to say! Thanks for documenting your build though.

TJryder
Learning to use the board
Learning to use the board
Posts: 31
Joined: July 29th, 2018, 1:03 pm
Stroker Displacement: 4.6
Vehicle Year: 2000
Vehicle Make: Jeep
Vehicle Model: TJ

Re: 4.6 crawler build - low end torque....

Post by TJryder » November 14th, 2018, 12:00 pm

Hi,

made some progress also today.

I did measure valve play, when extended 1" out:

Image

It reads roughly 0.15mm (0.006"). Is this still acceptable? I will most likely replace the valves so this value should also drop a bit...

Help ?

Than I tried my burs end other stuff I had in the shop to try to work on porting and smoothing out the rough edges and corners:

Ikea reading light came super handy :-)
Image

Image

OK. This looks like crap - I just tested different burs on the chamber... I will do better in the end:

Image

BR M
°O I I I I I I O°

TJryder
Learning to use the board
Learning to use the board
Posts: 31
Joined: July 29th, 2018, 1:03 pm
Stroker Displacement: 4.6
Vehicle Year: 2000
Vehicle Make: Jeep
Vehicle Model: TJ

Re: 4.6 crawler build - low end torque....

Post by TJryder » Yesterday, 9:18 am

Hi guys, anny oppinions on those valves?
°O I I I I I I O°

Russ Pottenger
I love JeepStrokers.com!!
I love JeepStrokers.com!!
Posts: 665
Joined: August 15th, 2009, 1:27 am
Stroker Displacement: 4.7
Vehicle Year: 2000
Vehicle Make: Jeep
Vehicle Model: Cherokee

Re: 4.6 crawler build - low end torque....

Post by Russ Pottenger » Yesterday, 8:31 pm

At a minimum are you planning on having the valve seats touched up and valves refaced?

TJryder
Learning to use the board
Learning to use the board
Posts: 31
Joined: July 29th, 2018, 1:03 pm
Stroker Displacement: 4.6
Vehicle Year: 2000
Vehicle Make: Jeep
Vehicle Model: TJ

Re: 4.6 crawler build - low end torque....

Post by TJryder » Today, 5:42 am

At minimum for sure seats resurfacing. Valves most likely new, lapped to seal.
I just wandered if play in spec to keep the standard bores or do I need to fit replacement guides?
°O I I I I I I O°

Russ Pottenger
I love JeepStrokers.com!!
I love JeepStrokers.com!!
Posts: 665
Joined: August 15th, 2009, 1:27 am
Stroker Displacement: 4.7
Vehicle Year: 2000
Vehicle Make: Jeep
Vehicle Model: Cherokee

Re: 4.6 crawler build - low end torque....

Post by Russ Pottenger » Today, 10:36 am

At roughly $70.00 to replace both intake and exhaust valves your probably smart to do that.

.0015 clearance for the intake and up to .0025 for the exhaust would be my recommendation.
Most importantly is to keep the contricity of the freshly ground seat to .001
Problem with alot of production shops is that they don’t stay on top of their equipment and there doing valve work with worn out pilots.

Post Reply

Who is online

Users browsing this forum: No registered users and 3 guests