AEM F/IC Basic Setup

Performance mods and Advanced Stroker discussion.
User avatar
gradon
Donator
Donator
Posts: 1353
Joined: February 13th, 2008, 5:33 pm
Stroker Displacement: 4.6/280ci
Vehicle Year: 1996
Vehicle Make: Jeep
Vehicle Model: Cherokee
Location: DC

Re: AEM F/IC Basic Setup

Post by gradon »

I found that 4.7Kohm-10Kohm resistors allowed you to offset the O2 voltages without the pcm fighting you.
User avatar
darkcorp
I made it to triple digits!
I made it to triple digits!
Posts: 101
Joined: November 14th, 2013, 12:21 am
Stroker Displacement: 4.6L
Vehicle Year: 1999
Vehicle Make: JEEP
Vehicle Model: GCh 4.0
Location: Kazan/Russia
Contact:

Re: AEM F/IC Basic Setup

Post by darkcorp »

Hi guys!

I've bought AEM FIC 6 1910 for my 4.6 stroker. I know for Chrysler engine I should use 1913 version to eliminate MIL for injectors but I've found only 1910 version in my country.

One of my mate uses AEM FIC 6 1910 without throwing MIL. He connected additional 6 old Jeep injectors from junkyard and it works well.

Is it right or I can add some inductor coils instead? If yes, then could you tell parameters of inductor?
1517200365364_bulletin.jpg
Inductor.png
You do not have the required permissions to view the files attached to this post.
User avatar
darkcorp
I made it to triple digits!
I made it to triple digits!
Posts: 101
Joined: November 14th, 2013, 12:21 am
Stroker Displacement: 4.6L
Vehicle Year: 1999
Vehicle Make: JEEP
Vehicle Model: GCh 4.0
Location: Kazan/Russia
Contact:

Re: AEM F/IC Basic Setup

Post by darkcorp »

I don't understand why one picture wasn't attached.
Inductor.png
You do not have the required permissions to view the files attached to this post.
User avatar
darkcorp
I made it to triple digits!
I made it to triple digits!
Posts: 101
Joined: November 14th, 2013, 12:21 am
Stroker Displacement: 4.6L
Vehicle Year: 1999
Vehicle Make: JEEP
Vehicle Model: GCh 4.0
Location: Kazan/Russia
Contact:

Re: AEM F/IC Basic Setup

Post by darkcorp »

Hi guys!
Can you show basic settings for AEM FIC 6 for Jeep?
I've installed AEM, but engine roughly starts and stop in second. MAP shows 9kpa instead of 100 kpa on stopped engine.
Cummins90
I made it to triple digits!
I made it to triple digits!
Posts: 146
Joined: May 14th, 2016, 10:29 am
Vehicle Year: 1996
Vehicle Make: Jeep
Vehicle Model: Cherokee

Re: AEM F/IC Basic Setup

Post by Cummins90 »

What is your map clamp voltage set to? Map is an intercept connection. Map "in" goes from the sensor to the FIC, map "out" goes from the FIC to the PCM.
User avatar
darkcorp
I made it to triple digits!
I made it to triple digits!
Posts: 101
Joined: November 14th, 2013, 12:21 am
Stroker Displacement: 4.6L
Vehicle Year: 1999
Vehicle Make: JEEP
Vehicle Model: GCh 4.0
Location: Kazan/Russia
Contact:

Re: AEM F/IC Basic Setup

Post by darkcorp »

Checked wiring, it's ok.
Gave 1.5V to MAF input to FIC (1.5V battery), AEM shows 1.5V in program and gives 1.5V to ecu.
Cummins90
I made it to triple digits!
I made it to triple digits!
Posts: 146
Joined: May 14th, 2016, 10:29 am
Vehicle Year: 1996
Vehicle Make: Jeep
Vehicle Model: Cherokee

Re: AEM F/IC Basic Setup

Post by Cummins90 »

Start a new thread detailing your set up. I can only assume what you have for a set up but try to Zero out your MAP map. In the settings menu put your map clamp max to 4.9v. Does it run? Does it run correctly with stock injectors and bypass harness?
User avatar
darkcorp
I made it to triple digits!
I made it to triple digits!
Posts: 101
Joined: November 14th, 2013, 12:21 am
Stroker Displacement: 4.6L
Vehicle Year: 1999
Vehicle Make: JEEP
Vehicle Model: GCh 4.0
Location: Kazan/Russia
Contact:

Re: AEM F/IC Basic Setup

Post by darkcorp »

Can you show me your setup settings please?

Here are mine
IMG_20180903_184629.jpg
You do not have the required permissions to view the files attached to this post.
User avatar
darkcorp
I made it to triple digits!
I made it to triple digits!
Posts: 101
Joined: November 14th, 2013, 12:21 am
Stroker Displacement: 4.6L
Vehicle Year: 1999
Vehicle Make: JEEP
Vehicle Model: GCh 4.0
Location: Kazan/Russia
Contact:

Re: AEM F/IC Basic Setup

Post by darkcorp »

Finally started!
Cummins90
I made it to triple digits!
I made it to triple digits!
Posts: 146
Joined: May 14th, 2016, 10:29 am
Vehicle Year: 1996
Vehicle Make: Jeep
Vehicle Model: Cherokee

Re: AEM F/IC Basic Setup

Post by Cummins90 »

What was it?
User avatar
darkcorp
I made it to triple digits!
I made it to triple digits!
Posts: 101
Joined: November 14th, 2013, 12:21 am
Stroker Displacement: 4.6L
Vehicle Year: 1999
Vehicle Make: JEEP
Vehicle Model: GCh 4.0
Location: Kazan/Russia
Contact:

Re: AEM F/IC Basic Setup

Post by darkcorp »

Couldn't say exactly. Maybe harness or maybe base settings.

How do you start to tune AEM FIC on stroker?
Cummins90
I made it to triple digits!
I made it to triple digits!
Posts: 146
Joined: May 14th, 2016, 10:29 am
Vehicle Year: 1996
Vehicle Make: Jeep
Vehicle Model: Cherokee

Re: AEM F/IC Basic Setup

Post by Cummins90 »

Start a new thread with the details of your build.
Post Reply

Who is online

Users browsing this forum: Amazon [Bot] and 16 guests