Welcome to www.JeepStrokers.com!!
Not yet a registered user? You are required to Register before you can post within this topic.

AEM F/IC Basic Setup

Performance mods and Advanced Stroker discussion.
User avatar
gradon
Donator
Donator
Posts: 1333
Joined: February 13th, 2008, 5:33 pm
Stroker Displacement: 4.6/280ci
Vehicle Year: 1996
Vehicle Make: Jeep
Vehicle Model: Cherokee
Location: DC

Re: AEM F/IC Basic Setup

Post by gradon » June 12th, 2014, 4:53 pm

I found that 4.7Kohm-10Kohm resistors allowed you to offset the O2 voltages without the pcm fighting you.

User avatar
darkcorp
Making Progress
Making Progress
Posts: 77
Joined: November 14th, 2013, 12:21 am
Vehicle Year: 1999
Vehicle Make: JEEP
Vehicle Model: GCh 4.0
Location: Kazan/Russia
Contact:

Re: AEM F/IC Basic Setup

Post by darkcorp » May 11th, 2018, 4:36 am

Hi guys!

I've bought AEM FIC 6 1910 for my 4.6 stroker. I know for Chrysler engine I should use 1913 version to eliminate MIL for injectors but I've found only 1910 version in my country.

One of my mate uses AEM FIC 6 1910 without throwing MIL. He connected additional 6 old Jeep injectors from junkyard and it works well.

Is it right or I can add some inductor coils instead? If yes, then could you tell parameters of inductor?
1517200365364_bulletin.jpg
Inductor.png
You do not have the required permissions to view the files attached to this post.

User avatar
darkcorp
Making Progress
Making Progress
Posts: 77
Joined: November 14th, 2013, 12:21 am
Vehicle Year: 1999
Vehicle Make: JEEP
Vehicle Model: GCh 4.0
Location: Kazan/Russia
Contact:

Re: AEM F/IC Basic Setup

Post by darkcorp » May 14th, 2018, 3:49 am

I don't understand why one picture wasn't attached.
Inductor.png
You do not have the required permissions to view the files attached to this post.

User avatar
darkcorp
Making Progress
Making Progress
Posts: 77
Joined: November 14th, 2013, 12:21 am
Vehicle Year: 1999
Vehicle Make: JEEP
Vehicle Model: GCh 4.0
Location: Kazan/Russia
Contact:

Re: AEM F/IC Basic Setup

Post by darkcorp » September 3rd, 2018, 6:44 am

Hi guys!
Can you show basic settings for AEM FIC 6 for Jeep?
I've installed AEM, but engine roughly starts and stop in second. MAP shows 9kpa instead of 100 kpa on stopped engine.

Cummins90
I think I'll order a "tab"
I think I'll order a "tab"
Posts: 47
Joined: May 14th, 2016, 10:29 am
Vehicle Year: 1996
Vehicle Make: Jeep
Vehicle Model: Cherokee

Re: AEM F/IC Basic Setup

Post by Cummins90 » September 3rd, 2018, 7:02 am

What is your map clamp voltage set to? Map is an intercept connection. Map "in" goes from the sensor to the FIC, map "out" goes from the FIC to the PCM.

User avatar
darkcorp
Making Progress
Making Progress
Posts: 77
Joined: November 14th, 2013, 12:21 am
Vehicle Year: 1999
Vehicle Make: JEEP
Vehicle Model: GCh 4.0
Location: Kazan/Russia
Contact:

Re: AEM F/IC Basic Setup

Post by darkcorp » September 3rd, 2018, 7:45 am

Checked wiring, it's ok.
Gave 1.5V to MAF input to FIC (1.5V battery), AEM shows 1.5V in program and gives 1.5V to ecu.

Cummins90
I think I'll order a "tab"
I think I'll order a "tab"
Posts: 47
Joined: May 14th, 2016, 10:29 am
Vehicle Year: 1996
Vehicle Make: Jeep
Vehicle Model: Cherokee

Re: AEM F/IC Basic Setup

Post by Cummins90 » September 3rd, 2018, 8:30 am

Start a new thread detailing your set up. I can only assume what you have for a set up but try to Zero out your MAP map. In the settings menu put your map clamp max to 4.9v. Does it run? Does it run correctly with stock injectors and bypass harness?

User avatar
darkcorp
Making Progress
Making Progress
Posts: 77
Joined: November 14th, 2013, 12:21 am
Vehicle Year: 1999
Vehicle Make: JEEP
Vehicle Model: GCh 4.0
Location: Kazan/Russia
Contact:

Re: AEM F/IC Basic Setup

Post by darkcorp » September 3rd, 2018, 8:47 am

Can you show me your setup settings please?

Here are mine
IMG_20180903_184629.jpg
You do not have the required permissions to view the files attached to this post.

User avatar
darkcorp
Making Progress
Making Progress
Posts: 77
Joined: November 14th, 2013, 12:21 am
Vehicle Year: 1999
Vehicle Make: JEEP
Vehicle Model: GCh 4.0
Location: Kazan/Russia
Contact:

Re: AEM F/IC Basic Setup

Post by darkcorp » September 3rd, 2018, 9:15 am

Finally started!

Cummins90
I think I'll order a "tab"
I think I'll order a "tab"
Posts: 47
Joined: May 14th, 2016, 10:29 am
Vehicle Year: 1996
Vehicle Make: Jeep
Vehicle Model: Cherokee

Re: AEM F/IC Basic Setup

Post by Cummins90 » September 3rd, 2018, 9:23 am

What was it?

User avatar
darkcorp
Making Progress
Making Progress
Posts: 77
Joined: November 14th, 2013, 12:21 am
Vehicle Year: 1999
Vehicle Make: JEEP
Vehicle Model: GCh 4.0
Location: Kazan/Russia
Contact:

Re: AEM F/IC Basic Setup

Post by darkcorp » September 3rd, 2018, 12:24 pm

Couldn't say exactly. Maybe harness or maybe base settings.

How do you start to tune AEM FIC on stroker?

Cummins90
I think I'll order a "tab"
I think I'll order a "tab"
Posts: 47
Joined: May 14th, 2016, 10:29 am
Vehicle Year: 1996
Vehicle Make: Jeep
Vehicle Model: Cherokee

Re: AEM F/IC Basic Setup

Post by Cummins90 » September 3rd, 2018, 1:17 pm

Start a new thread with the details of your build.

Post Reply

Who is online

Users browsing this forum: Baidu [Spider] and 5 guests